TPS259531DSGR

Texas Instruments
595-TPS259531DSGR
TPS259531DSGR

製造商:

說明:
熱插拔電壓控制器 2.7-V to 18-V 34m&O mega; 0.5-4A eFuse A A 595-TPS259531DSGT

ECAD模型:
下載免費的庫載入器,為ECAD工具轉換此文件。瞭解更多關於 ECAD 型號的資訊。

庫存量: 23,374

庫存:
23,374 可立即送貨
工廠前置作業時間:
12 週 工廠預計生產時間數量大於所顯示的數量。
最少: 1   多個: 1
單價:
HK$-.--
總價:
HK$-.--
估計關稅:
包裝:
完整捲(訂購多個3000)

Pricing (HKD)

數量 單價
總價
零卷 / MouseReel™
HK$8.30 HK$8.30
HK$5.97 HK$59.70
HK$5.38 HK$134.50
HK$4.74 HK$474.00
HK$4.44 HK$1,110.00
HK$4.25 HK$2,125.00
HK$4.10 HK$4,100.00
完整捲(訂購多個3000)
HK$3.62 HK$10,860.00
† HK$55.00 MouseReel™費用將加入您的購物車內並自動計算。所有MouseReel™訂單均不能取消和不能退換。

備用包裝

製造商 元件編號:
包裝:
Reel, Cut Tape, MouseReel
供貨情況:
庫存量
價格:
HK$9.29
最小值:
1

相似產品

Texas Instruments TPS259531DSGT
Texas Instruments
熱插拔電壓控制器 2.7-V to 18-V 34m&O mega; 0.5-4A eFuse A A 595-TPS259531DSGR

商品屬性 屬性值 選擇屬性
Texas Instruments
產品類型: 熱插拔電壓控制器
RoHS:  
Controllers & Switches
500 mA to 4 A
18 V
2.7 V
1 Channel
- 40 C
+ 125 C
SMD/SMT
WSON-8
Reel
Cut Tape
MouseReel
Yes
品牌: Texas Instruments
輸入/電源電壓 - 最大值: 18 V
輸入/電源電壓 - 最小值: 2.7 V
濕度敏感: Yes
產品類型: Hot Swap Voltage Controllers
系列: TPS2595
原廠包裝數量: 3000
子類別: PMIC - Power Management ICs
每件重量: 12 mg
找到產品:
若要顯示類似商品,請選取至少一個核選方塊
至少選中以上一個核取方塊以顯示在此類別中類似的產品。
所選屬性: 0

此功能需要啟用JavaScript。

CNHTS:
8542399000
CAHTS:
8542390000
USHTS:
8542390090
MXHTS:
8542399999
ECCN:
EAR99

TPS2595 12V電子保險絲

Texas Instruments TPS2595 12V電子保險絲具備過電壓保護功能,提供使用極少外部元件的電路保護和電源管理解決方案。該元件具有2.7V至18V的寬輸入電壓範圍,絕對最大電壓為20V。多種保護模式可防止過載、短路、電壓浪湧和過大的湧入電流。限流電阻上的壓降可精確測量輸出負載電流。輸出限流電平也可以使用單個外部電阻來設定。透過具有辨別湧入電流需求的應用,可使用單個外部電容設定輸出轉換率。Texas Instruments TPS2595的工作溫度範圍為-40°C +125°C。

LM5060 High-Side Protection Controllers

Texas Instruments LM5060 High-Side Protection Controllers with Low Quiescent Current offers intelligent control of a high-side N-channel MOSFET during normal on/off transitions and fault conditions. The constant rise time of the output voltage results from the inrush current control. Both an Input UVLO (with hysteresis) and a programmable input OVP are provided, with an enable input offering a remote on or off control. The initial start-up VGS fault detection delay time, the transition VDS fault detection delay time, and the continuous over-current VDS fault detection delay time is programmed from a single capacitor. The MOSFET is latched off until either the enable input, or the UVLO input is toggled low and then high when a detected fault condition persists longer than the allowed fault delay time.